Adding IDE Drives
Though modern machines will often include a single IDE connection for the sake of backwards compatibility, most machines from the IDE era of computing were equipped with two IDE sockets – If you want to put a 3.5" drive into a 5.25" drive bay, get an adapter that holds the drive and fits into the 5.25" bay. Well, looking at the back of the device, we have 3 pairs of pins. I am currently running a Maxtor 200GB SATA drive as the master and a Maxtor 120GB IDE drive as the slave. this contact form
Preview post Submit post Cancel post You are reporting the following post: Mixing SATA and IDE drives in a system? Here's how the IDE connector sockets on the motherboard look, along with the ribbon cable that goes from the motherboard socket into the back of any IDE drive: PATA Photos (Wikipedia This is where you want to put an IDE drive into a SATA-only motherboard or vice versa. The example I/O controller card below gives you one SATA socket, one PATA socket, and one eSATA (external SATA) socket. http://www.makeuseof.com/tag/install-ide-hard-drive/
Ide Hard Drive Jumper Settings
You can connect either one or two IDE drives to an IDE ribbon cable. When you reboot your machine the BIOS should automatically detect the new hard drive. Let's Begin Unpack everything.
Simply slide the drive into the cage so that the mounting holes on the drive match up to the holes on the cage. EaseUS softwar… Related Products Data Recovery Software Data Backup Software Partition Manager Software PC Transfer Software Mac System Utility File Sync Utility Top 10 Hot Articles Recover Pictures after Factory Reset Flag Permalink This was helpful (1) Collapse - New computers often handle this well by jrfree / July 22, 2005 6:42 AM PDT In reply to: Mixing SATA and IDE drives Seagate Ide Hard Drive Jumper Settings It's white and it has a female connector that goes into the 4-pin male connector on the back of the disk drive.
The jumpers are the set of pins on the back of the hard drive. How To Connect Ide Hard Drive To Sata Motherboard The master device is connected in the middle of the cable, and the slave at the end of the cable. Set The Jumpers & Plug In Since I only have a single IDE CD-ROM and single hard disk to show you today (as well as only a single physical IDE connector
Background On IDE Interfaces IDE was a significant limiting factor in older PCs.
TigerDirect 364,279 views 5:57 Add a second hard drive to your pc - Duration: 9:18. Western Digital Ide Hard Drive Jumper Settings Format the drive. See Formatting a Hard Disk under DOS Format. Just connect and copy over your data.
How To Connect Ide Hard Drive To Sata Motherboard
When running more than one OS on multiple drives you can use this option, or if running a properly installed NT/2000/XP, you can add boot options into the boot.ini. http://www.osnews.com/story/25660/How_to_Integrate_SATA_and_IDE_Drives Sign in 11 Loading... Ide Hard Drive Jumper Settings EditRelated wikiHows How to Ground Yourself to Avoid Destroying a Computer with Electrostatic Discharge How to Format a Hard Drive How to Build an External Hard Drive How to Back up How To Connect Ide Hard Drive To Motherboard BUY NOW FREE TRIAL Data Recovery Wizard for Mac Best Mac data recovery software recovers whatever you lost from Mac machines & storage devices.
It is safer to use the same type that is already installed, even if the sockets for another type also appear to be present. http://neoppidum.com/hard-drive/advice-regarding-external-hard-drives.php Two if you're lazy and only screw things in on the side. Be sure to remove any screws that fasten the cover to the case and set them aside in a safe place.3 Unplugging Current Drive Cables Remove IDE and Power Cables Because Windows, and system, detect HD SATA and primary IDE HD in ID 0 Bus 0 ATAPI, i move my IDE HDs to secondary IDE Channel e move my DVD/CDROM to How To Install Ide Hard Drive
Do This First! However, if you have an older computer you may find this cable is not available. Steps 1 Check if you need the IDE (parallel ATA) or Serial ATA. http://neoppidum.com/hard-drive/addind-hard-drives.php Community Q&A Search Add New Question How do I view data from an extra hard drive after I have connected it to my laptop?
The first step is to insert the drive into a free drive bay (if you are unsure what a drive bay looks like then see fig 1.3 further up this page). Ide Cable Select This black sleeve is what you will use to configure your device as one of the options below. What is IDE ?
Needle-nose pliers for removing or adding jumpers.
If not, select the auto-detect option. There is a notch on one side of the connector to prevent you plugging it in the wrong way, so make sure you align that. For an example of a drive bay see fig 1.3 on the left. How Many Hard Drives Can Be Connected To A Single Ide Cable On my fairly modern motherboard, the cable is actually colour coded so you know which end plugs where – but more than likely your old PC won’t be, so you’ll need
If you're having difficulty, it's a good idea to consult your manual on how your particular case is removed. With PATA you didn't normally mix hard and optical drives on the same IDE cable because it can slow data access times. And there are some ways to partition the hard drive actually, say, partition the hard drive under Disk Management or use the third party partition manager tool like EaseUS partition Master his comment is here Please consult the documentation that came with your motherboard or computer for additional information.Continue Reading Up Next Up Next List How to Install Cold Cathode Fluorescent Lights Up Next List
Sign in Transcript Statistics Add translations 3,070 views 30 Like this video? Flag Permalink This was helpful (0) Collapse - New SATA HD booting mantining old IDE HDs. Removing an old IDE hard drive If you are replacing your current IDE hard drive either with a bigger drive of the same type or a new SATA device then the Storage forum About This ForumCNET's Forum on storage is the best source for finding help, troubleshooting, and getting buying advice from a community of experts.
Make sure both of the drives aren't set for the same setting (master or slave). Jason Hammack 178,103 views 6:49 Adding an IDE hard drive to a modern motherboard - Duration: 6:05. Prior settings of the jumpers to "slave" would result in no boot screen at all upon powering on. Show more Language: English Content location: United States Restricted Mode: Off History Help Loading...
Flag as duplicate Thanks! Close Yeah, keep it Undo Close This video is unavailable. I installed Windows on the SATA drive.I built this computer myself and haven't had any problems with this configuration. But there are also transition motherboards that have SATA sockets and one or two PATA sockets.
My hard drive is slow: Make sure you have your CD/DVD drives plugged into a different channel/cable. Note that if both the master and the slave are available on the slot you are using (primary or secondary), set the hard drive to master. (fig. 4) Note that if When inserting the fixing screws you will find it easier if you do not tighten them completely until you have all 4 in place, this will aid alignment. bentsnake 772,574 views 8:08 Introduction to a Hard Disk of a Computer (Hindi) (हिन्दी) - Duration: 13:51.
Flag Permalink This was helpful (0) Collapse - It's fine by ackmondual / July 22, 2005 11:48 AM PDT In reply to: Mixing SATA and IDE drives in a system? Carefully but firmly plug the IDE and power cables in and then move onto finishing the installation below. This is why I did. Please try again now or at a later time.
I have a sata HD running as my main drive and another IDE HD, formerly my main one, that I use for music files and backup storage.
© Copyright 2017 neoppidum.com. All rights reserved.